Home/Applications/Oxygen Analyzer for H2S-Bearing Natural Gas

Oxygen Analyzer for H2S-Bearing Natural Gas

Intended for dry, non-condensing sample gas that contains H2S.

Sample line from a pipeline to an analyzer enclosureAbstract diagram of a pipeline, a sample line, and an analyzer enclosure. The drawing does not show a sensor, cell block, fiber, or RTD.PipelineAnalyzer enclosuresample line onlySchematic only. Sample path from the pipeline to the enclosure.
Schematic only. The drawing shows a sample line from a pipeline to an analyzer enclosure.

Last updated:

Produced gas can carry hydrogen sulfide and carbon dioxide. OxyScout™ uses a proprietary, fully optical sensor for continuous oxygen measurement. OxyScout is intended for dry, non-condensing sample gas that contains H2S. Wet sour gas is a different application condition; contact Standard Sensors to review suitability before specifying the analyzer for wet sour service.

The U.S. Energy Information Administration states that wellhead natural gas may contain nonhydrocarbons such as hydrogen sulfide and carbon dioxide. That statement supports the composition sentence above. The cross-sensitivity statements on this page are OxyScout statements and are not taken from that source. Source: EIA, Natural gas explained.

Does H2S change the oxygen reading?

The optical sensor has no cross-sensitivity to H2S. In field testing of the sensing technology, the sensor ran in gas containing high H2S concentration (percent level) with no effect. OxyScout is intended for dry, non-condensing sample gas that contains H2S. For wet sour gas, contact Standard Sensors to review the application suitability.

The percent-level field test describes the sensing technology. That test is not a published H2S percentage or ppm service limit for fittings or other hardware, and this page does not state one.

Does CO2 change the oxygen reading?

The sensing technology has been field tested in up to 100% CO2 with no effect on the reading and no damage.

What does liquid water do to the reading?

Liquid water offsets the reading temporarily. Once the sample path is purged, the reading recovers. OxyScout is specified for non-condensing sample conditions. If the sample can be wet or condensing in sour service, request an application review.

What else can interfere with the sensor?

Organic solvent vapors, chlorine gas, and nitrogen dioxide (NO2) interfere with the sensor. Methane, CO2, and H2S do not interfere.

Which models and outputs apply?

Ultra-Trace OxyScout-UT (0–50 ppm), Trace OxyScout-T (0–1,000 ppm), and Percent OxyScout-P (0–1 / 0–10 / 0–21 %vol) share the same communications. SKU and MPN are identical for each model. Outputs are a 4–20 mA loop (current sink) and RS-485 Modbus RTU. Power is 9–36 VDC. Input pressure is up to 250 psi without the optional flowmeter. Operating temperature is 0 to 50 °C. The enclosure is IP67. The analyzer weighs 4 lb. OxyScout is engineered for Class 1 Division 2 (Zone 2) hazardous areas. OxyScout is built in the USA, and covered by a 12-month warranty from shipment that includes the sensor.

Gas compatibility for OxyScout

Gas or conditionEffect on OxyScout
Natural gas, methane (CH4)No cross-sensitivity
Hydrogen sulfide (H2S)No cross-sensitivity of the optical sensor. In field testing of the sensing technology, high H2S concentration (percent level) had no effect. Intended for dry, non-condensing sample gas that contains H2S. Wet sour gas requires application review.
Carbon dioxide (CO2)No cross-sensitivity. Field tested up to 100%.
Liquid waterTemporary offset. Recovers after purging.
Other organic solvent vaporsInterferes
Chlorine gas, nitrogen dioxide (NO2)Interferes
FAQ

Frequently asked questions

Does H2S affect OxyScout?

No. The optical sensor has no cross-sensitivity to H2S. In field testing of the sensing technology, the sensor ran in gas containing high H2S concentration (percent level) with no effect. OxyScout is intended for dry, non-condensing sample gas that contains H2S. For wet sour gas, contact Standard Sensors to review the application suitability.

Does CO2 affect OxyScout?

No. The sensing technology has been field tested in up to 100% CO2 with no effect on the reading and no damage.

What can interfere with the sensor?

Organic solvent vapors, chlorine gas, and nitrogen dioxide (NO2) interfere with the sensor. Methane, CO2, and H2S do not interfere.

What happens if liquid water reaches the sensor?

Liquid water offsets the reading temporarily. Once the sample path is purged, the reading recovers. OxyScout is specified for non-condensing sample conditions.

How long does the optical sensor last?

The sensor is covered by the 12-month warranty. Standard Sensors expects more than one year of service, and longer in clean, dry sample conditions. Long-term life data is still being collected.

How is OxyScout calibrated?

A two-point calibration with zero gas and span gas is recommended. A one-point calibration is acceptable. Drift between calibrations depends on the sample rate set and on process quality. Typically, a 1–2 month interval results in low single-digit ppm of oxygen drift across OxyScout models. Drift between calibrations is not the same as detection limit or accuracy.

How fast does OxyScout recover after exposure to air?

Air doesn't damage or poison the OxyScout optical sensor. Once process gas is flowing again, the reading typically recovers within minutes. Electrochemical trace O₂ cells can be used up or permanently damaged by extended air exposure.

Where is OxyScout built, and what are the warranty and lead time?

OxyScout is built in the USA. The standard warranty is 12 months from shipment and includes the sensor. Lead time can be less than one week.

Talk to an engineer about your application

Book a 30-minute meeting to review your application and we'll send you a quote after the call.

Get a Quote